N038785 Air Compressor Piston Rod Kit For Dewalt Black&Decker Craftsman Bostitch

Description

N038785 Air Compressor Piston Rod Kit For Dewalt Black&Decker Craftsman Bostitch 1.Fitment: for Craftsman Devildiss Dewalt ,Black and Decker, Bostitch. Does not fit any 2 cylinder units. 2.Compatible with Model: 【Fits for DeWalt models】D55146 , D55167 , D55168 All types numbers. 【Fits for Bostitch models】CAP1615-OF Type 0, CAP1645-OF Type 1【Fits for Black and Decker models】919-16760,919-16762,919-16761,919-16763. 3.Material: The kit is constructed from high mechanical strength 6061 Aluminum and rubber, ensure the kit no cracks and longterm service for your air compressor.. 4.Note: Fits 73 mm ( 2-7/8") Cylinder Bore. Ensure the OD of the cylinder Sleeve is right for your cylinder bore before purchase. 5.Function: To rebuild a piston cylinder in the compressor. You can replace o-rings on valve plate , cylinder sleeve , connecting rod and piston ring in the compressor. It is recommended that you release air and unplug the air compressor before you install this kit. You will need a wrench set to replace this part. Great Compatibility: Please check your model's fitment before purchasing. Compatible with D55146 Type 1, Type 2, Type 3, Type 4, Type 5. Compatible with D55167 Type 1, Type 2, Type 3, Type 4, Type 5. Compatible with D55168 Type 1, Type 2, Type 3, Type 4, Type 5, Type 6, Type 7. Compatible with CAP1615-OF Type 0. Compatible with CAP1645-OF Type 1. Compatible with FMFP70978 Type 1. Compatible with 919-16755 Type 0, Type 1. Compatible with 919-16760 Type 0. Compatible with 919-16761 Type 0. Compatible with 919-16762 Type 0, Type 1. Compatible with 919-16763 Type 0, Type 1. Compatible with 919-16770 Type 0, Type 1. Compatible with 919-16771 Type 0, Type 1. Installtion Guide Step 1. After disassemble the pump head, Remove the fan mounting bolt and pull the fan off Remove the piston and old sleeve. Step 2. Install the new compression ring Place the new compression ring on the top of the piston. Reinstall the piston cap and Torx screw. Step 3. Insert the piston rod into the sleeve. Slide the piston into the new cylinder sleeve. Insert the piston and cylinder sleeve into the pump body. Step 4. Reinstall the piston and the fan Push the piston connecting rod onto the eccentric bearing. Align the piston connecting rod flush with the eccentric bearing. Tighten the piston connecting rod Torx screw to 48 inch-pounds using a torque wrench Step 5. Replace the both new valve plate seals on the valve plate assembly, then cover to the piston back. Install the new upper valve plate seal. Install the new lower valve plate seal. Step 6.Reinstall the pump head mounting bolts. Position the pump head over the new valve plate with the muffler side of the pump head over the reed valves on the valve plate. Package Includes: 1 x Connecting Rod, 1 x Piston Ring, 1 x Cylinder Sleeve, 2 x O-Ring that go on the valve plate. Payment methods accepted: Payoneer . Our Payoneer account allows you to pay by credit card, debit card and your paypal balance. 1.Orders will be ship out within 1-3 business days after payment has cleared. Orders from Saturdays, Sundays or holidays will process on next business day and will be ship within 24 hours. 2.All of the items are shipped from our Warehouse in USA. 1. Any defective items received can be replaced or refunded. Please contact us with the item number, eBay ID and defect description within 60 days after the date of package arrived. No Claim will be accept after 60 days. 2. Return shipping fee is the responsibility of buyer unless the return is a result of our mistake. And all NON-seller mistake returns for refund are subject to 20% re-stocking fee. If you have any questions, please feel free to email our service specialists 24 Hours a Day, and we will reply you ASAP. If no response within 24 Hours, please check the spam of mail box or kindly re-send it to us. Please note that our product is an aftermarket product (non-OEM). The parts we offer in this listing are an O.E. alternative; they are not produced by O.E. Manufacturers. All names, numbers, symbols and descriptions are used for reference purposes only. If you mind, please do not place an order. Please contact us before leaving Neutral or Negative feedback if you are not satisfied our service or products. Good communication is helpful for both of us to resolve any problems and issues. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers. 1.Fitment: for Craftsman Devildiss Dewalt ,Black and Decker, Bostitch. Does not fit any 2 cylinder units. 2.Compatible with Model: 【Fits for DeWalt models】D55146 , D55167 , D55168 All types numbers. 【Fits for Bostitch models】CAP1615-OF Type 0, CAP1645-OF Type 1【Fits for Black and Decker models】919-16760,919-16762,919-16761,919-16763. 3.Material: The kit is constructed from high mechanical strength 6061 Aluminum and rubber, ensure the kit no cracks and longterm service for your air compressor.. 4.Note: Fits 73 mm ( 2-7/8") Cylinder Bore. Ensure the OD of the cylinder Sleeve is right for your cylinder bore before purchase. 5.Function: To rebuild a piston cylinder in the compressor. You can replace o-rings on valve plate , cylinder sleeve , connecting rod and piston ring in the compressor. It is recommended that you release air and unplug the air compressor before you install this kit. You will need a wrench set to replace this part. Great Compatibility: Please check your model's fitment before purchasing. Compatible with D55146 Type 1, Type 2, Type 3, Type 4, Type 5. Compatible with D55167 Type 1, Type 2, Type 3, Type 4, Type 5. Compatible with D55168 Type 1, Type 2, Type 3, Type 4, Type 5, Type 6, Type 7. Compatible with CAP1615-OF Type 0. Compatible with CAP1645-OF Type 1. Compatible with FMFP70978 Type 1. Compatible with 919-16755 Type 0, Type 1. Compatible with 919-16760 Type 0. Compatible with 919-16761 Type 0. Compatible with 919-16762 Type 0, Type 1. Compatible with 919-16763 Type 0, Type 1. Compatible with 919-16770 Type 0, Type 1. Compatible with 919-16771 Type 0, Type 1. Installtion Guide Step 1. After disassemble the pump head, Remove the fan mounting bolt and pull the fan off Remove the piston and old sleeve. Step 2. Install the new compression ring Place the new compression ring on the top of the piston. Reinstall the piston cap and Torx screw. Step 3. Insert the piston rod into the sleeve. Slide the piston into the new cylinder sleeve. Insert the piston and cylinder sleeve into the pump body. Step 4. Reinstall the piston and the fan Push the piston connecting rod onto the eccentric bearing. Align the piston connecting rod flush with the eccentric bearing. Tighten the piston connecting rod Torx screw to 48 inch-pounds using a torque wrench Step 5. Replace the both new valve plate seals on the valve plate assembly, then cover to the piston back. Install the new upper valve plate seal. Install the new lower valve plate seal. Step 6.Reinstall the pump head mounting bolts. Position the pump head over the new valve plate with the muffler side of the pump head over the reed valves on the valve plate. Package Includes: 1 x Connecting Rod, 1 x Piston Ring, 1 x Cylinder Sleeve, 2 x O-Ring that go on the valve plate.